• +7 (495) 777-25-41
  • +38 (056) 785-39-23
    +38 (056) 785-39-23
  • +7 (3412) 26-03-80
  • +7(3422) 99-46-32
  • +7 (3812) 20-80-31
  • +7 (391) 205-17-79
  • +7 (8432) 07-01-39
  • +7 (383) 207-81-90
  • +49 (30) 217-888-05

Tape, round, wire 50NP - alloy 50

Tape, round, wire 50NP - alloy 50

General characteristics

To soft magnetic alloys are alloys based on iron, alloyed with Nickel and cobalt. Their composition is a particularly pure ferromagnetic iron or low carbon electrical steel (non-alloy, silicon). It nizkotemperaturnye precision alloys with high Nickel based ferrimagnetic and ferromagnetic powder, composite. Such alloys are melted in a special metallurgical furnaces. Ready bullion subsequently subjected to forging or rolling. Magnetically soft alloy has a high technical saturation induction, high magnetic permeability. Used in the manufacture of transformers, magnetic AC magnetic field, electronic and electrical parts, systems automation, remote control, computer measurement technology.

Relevance

Alloy 50NP used in the manufacture of small cores, magdalinova power transformers, chokes, parts of magnetic circuits, a relay operated with a small magnetization, or without it at high inductions. Having a high value of initial magnetic permeability soft magnetic alloy 50NP can be magnetized to saturation in weak fields.

Chemical composition 50N percent, according to GOST 10994- -74

P Fe Cu S Si Mn Ni C
up to 0.02 48.33 — 50.55 to 0.2 up to 0.02 0.15 — 0.3 0.3 — 0.6 to 0.3 to 0.03
Welding:
weldability limited — welding is possible in the process of heating up to temp. 100−120? C and further thermal treatment
konovalivka in order to obtain quality welded joints, it is necessary to perform additional operations: during welding heating up to temp. 200−300°C, heat treatment (annealing) after welding.
Welded without any restrictions — welding is carried out without further heat treatment and pre-heating.

The physical characteristics of the brand 50N.

C l R 10 9 r a 10 6 T E 10 — 5
J/(kg·deg) W/(m·deg) Ohm·m kg/m3 1/Deg Grad MPa
        8,9 100  
    450 8200   20 1,6
Physical characteristics of this brand of alloy:
— 1st kind of modulus of elasticity, [MPa] — E
— The heat capacity of the material (or the ratio of teploprovodna.), in [W/(m·deg)] -l
— The temperature required to obtain these properties, [Grad] — T
— linear coefficient. temp. extensions to [1/Deg] (temp. the interval 20o), -a
— electrical resistivity, [Ohm·m] -R
— The density of this material, [kg/m3] -r
— the specific heat capacity of the material in [j/(kg·deg)] (temp. the interval 20 ° C) -C

Magnetic characteristics:

the coercive force (not more than) [A/m ] Hc
the magnetic permeability (not above) [ MH/m ] Umax
— specific losses (no higher) frequency 50 Hz, magnetic induction of 1.0 T [ W/kg ] P1.0/50
— T magnetic induction intensity of a magnetic field of not less than 100, in a magnetic field [ A/m ] B100

Mechanical characteristics of 50N at a temperature of 20oC.

Products Eg. d5 Dimensions blower SB Heat treatment. sT y KCU
Tape, in accordance with GOST 10160−75   35   440   145 60  
- - % mm MPa - MPa % kJ / m2
sugartown. tape, in accordance with GOST 10160−75   3   780   685 15  
Mechanical characteristics:
— Short-term tensile strength in [MPa] blower SB
— Yield strength (limit of proportionality) for the residual strain, [MPa] sT
— at break elongation in [ % ] d5
— narrowing of the relative in [ % ] y
— the viscosity of the shock, in [ kJ / m2] KCU
— Brinell hardness [MPa] HB

Application

Precision alloy brand 50N are applied in the field of precision machine tools for the production of various electronic precision instruments, household appliances, innovative technologies, laser technology, in products of Metrology and measurement technology.

Buy at the best price.

The range of products from alloy 50N, presented by LLC «AVEK global» can satisfy almost any consumer. This alloy belongs to the popular group of steel products due to its real value and variety of output options. Quality metal products is guaranteed absolute observance of all technological norms of production. In the absence of the base performance required of the product and if necessary other option products, we can produce custom sizes to order.